收藏本站
Serial Number iButton
1-Wire Signaling
The DS1990R requires strict protocols to ensure data
integrity. The protocol consists of four types of signaling
on one line: reset sequence with reset pulse and pres-
ence pulse, write-zero, write-one, and read-data.
Except for the presence pulse, the bus master initiates
all these signals.
To get from idle to active, the voltage on the 1-Wire line
needs to fall from V PUP to below V ILMAX . To get from
active to idle, the voltage needs to rise from V ILMAX to
above V IHMIN . The time it takes for the voltage to make
this rise, referenced as ε in Figure 6, depends on the
value of the pullup resistor (R PUP ) and capacitance of
the 1-Wire network attached.
The initialization sequence required to begin any com-
munication with the DS1990R is shown in Figure 6. A
reset pulse followed by a presence pulse indicates that
the DS1990R is ready to receive a ROM function com-
mand. If the bus master uses slew-rate control on the
falling edge, it must pull down the line for t RSTL + t F to
compensate for the edge.
After the bus master has released the line, it goes into
receive mode (Rx). Now the 1-Wire bus is pulled to
V PUP through the pullup resistor or, in the case of a
DS2480B driver, by active circuitry. When the V IHMIN is
crossed, the DS1990R waits for t PDH and then transmits
a presence pulse by pulling the line low for t PDL . To
MASTER Tx "RESET PULSE"
V PUP
V IHMIN
V ILMAX
ε
detect a presence pulse, the master must test the logi-
cal state of the 1-Wire line at t MSP .
Read/Write Time Slots
Data communication with the DS1990R takes place in
time slots that carry a single bit each. Write time slots
transport data from bus master to slave. Read time
slots transfer data from slave to master. The definitions
of the write and read time slots are illustrated in
Figure 7.
All communication begins with the master pulling the
data line low. As the voltage on the 1-Wire line falls
below V ILMAX , the DS1990R starts its internal timing
generator that determines when the data line is sam-
pled during a write time slot and how long data is valid
during a read time slot.
Master-to-Slave
For a write-one time slot, the voltage on the data line
must have risen above V IHMIN after the write-one low
time t W1LMAX is expired. For a write-zero time slot, the
voltage on the data line must stay below V ILMAX until
the write-zero low time t W0LMIN is expired. For most reli-
able communication, the voltage on the data line
should not exceed V ILMAX during the entire t W0L win-
dow. After the voltage has risen above V IHMIN , the
DS1990R needs a recovery time t REC before it is ready
for the next time slot.
MASTER Rx "PRESENCE PULSE"
t MSP
0V
t RSTL
t PDH
t PDL
t REC
t F
t RSTH
RESISTOR
Figure 6. Initialization Procedure: Reset and Presence Pulses
MASTER
DS1990R
_______________________________________________________________________________________
7
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
DS1993L-F5+ IBUTTON MEMORY 4KBit F5
DS1995L-F5+ IBUTTON MEMORY 16KBit F5
DS1996L-F5+ IBUTTON MEMORY 64KBit F5
DS9092K# KIT IBUTTON STARTER
DS9502P+T&R DIODE ESD PROTECTION 6-TSOC
DS9503P+ DIODE ESD PROTECTION W/RES 6TSOC
DSL70 E6327 DIODES TVS ARRAY R-R SOT-143
DT-2R48-B6 SWITCH PLUNGER DPDT 10A SCREW
相关代理商/技术参数
DS1990R-F5+W 功能描述:序列号注册 RoHS:否 制造商:Maxim Integrated 数据总线宽度: 电源电压-最大: 电源电压-最小: 最大工作温度: 最小工作温度: 安装风格: 封装 / 箱体:
DS1990-序列号IBUTTON 制造商:未知厂家 制造商全称:未知厂家 功能描述:
DS1991 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:MultiKey iButton
DS1991L 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC
DS1991L+F5 制造商:Maxim Integrated Products 功能描述:IC MEMORY I BUTTON 1991
DS1991L-004-000+ 功能描述:iButton RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1991L-702-00B+ 功能描述:iButton RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1991L-F5 功能描述:iButton RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated